Tuesday Tutorial: Glitter Name Bunting

Glitter Name Bunting Tutorial by Under a Glass Sky

Yes, you’re right, my last tutorial was about glitter too. But then glitter is worthy of repetition.

A trend has been emerging with my recent crafting projects….glitter. And why the heck not? After all, glitter is the quintessential crafting supply, and everything is better with a good sprinkle of the stuff.

I bought a stash of glitter card ages ago, and did the usual thing of ‘saving it for something special’. And what could be more special than my niece’s first birthday?! Having decided I wanted to make something glittery for her, I thought about what a one year old could best make use of…..she’s mostly pointing at me and laughing right now though, and doesn’t seem to be in need of anything other than whatever food is out of her reach, so I opted for for something to decorate her bedroom. And because (I think it’s fair to say) I’m pretty bunting obsessed, that’s what my first thought ran to!

You don’t need any crazy equipment or mad skills for this DIY, but it does take some precision and patience. The result is pretty rewarding though I think!

Glitter Name Bunting Tutorial by Under a Glass Sky

What you will need:

  • Glitter card
  • Wooden pennants with pre-drilled holes (enough for each letter of the name)
  • Mod Podge or PVA glue
  • Ribbon (enough to go across the width of each pennant, plus about 30cm extra)
  • A plastic spatula
  • Craft knife or scalpel
  • Metal rule
  • A pencil
  • Small scissors

How to make it:

  • Place your first pennant on the back of a piece of glitter card and trace around it with a pencil as close as you can get
  • Cut the glitter card with scalpel and ruler or scissors if you prefer, and check it up against the pennant to see that it fits
  • Now give the pennant a good generous coat of glue….it’s better to have too much on there than too little
  • Carefully place the glitter card onto the pennant, squaring it up quickly before the glue dries to ensure all the edges are aligned
  • Press firmly down on the card so that any excess glue comes out at the sides
  • Use the spatula to remove this excess by sliding the flat edge along the side of the pennant….this will also help to nicely seal the edges
  • Repeat this for all your pennants and then set them aside to dry for a couple of hours
  • Whilst you wait, cut out your letters from the glitter card…..I used the pencil to draw onto the back of the card then cut around that, but remember to draw in reverse
  • Once the newly glittered pennants are dry, arrange them in the order you’d like them and offer up each letter to check that the colours contrast well enough to see them
  • Apply glue to the back of your first letter, again using plenty as you’ll need a good coat to get in between the bumpy glittery surface
  • Carefully place the letter on the pennant, check you’re happy with the positioning, and press down firmly
  • Again, use the spatula to remove any excess, although don’t worry too much as the glue will dry clear
  • Repeat for each pennant and allow to dry well, preferably over night
  • Now you just need to thread the pennants together by cutting through the glitter card to reveal the hole in the wood with the scalpel, and posting the ribbon through each hole of each pennant, then moving on to the next
  • Finally, tie a knot in each end to stop the pennants moving about, and you’re done!

If you find it tricky to get hold of some wooden pennants (I got mine from an online craft shop who sell lots of laser cut MDF shapes) you could always cut them yourself from foamex.

I also made a single pennant with a star shape on it for a friend’s birthday, and of course you could apply any pattern to your bunting, or even just leave it plain in all its glittery glory!

Happy glittering!

Ems x

 

Advertisements

Tuesday Tutorial: Purple Glitter Jewellery for Willow Foundation

Purple glitter jewellery tutorial

Last Saturday I was lucky enough to attend a friend’s “Purple Party” to help raise funds for Willow Foundation*. Clare is running the London Marathon for the charity this year, and so put together the brilliant themed party to add to her fundraising target. There were purple cocktails, purple food, a purple photo booth and the whole place was decked out in purple, including the guests!

Being a bit low on purple things to wear myself, I decided to make some purple glittery treasures, with extra for Clare to sell on the night. And because I know everyone loves glitter (not to mention with Half Term in full swing!) I thought I’d share a little tutorial for how to make them. The batch I made took a while because there were so many, but one or two would be very quick to make, and super easy too! You can buy everything you need easily and inexpensively at a craft shop or online.

Purple glitter jewellery tutorial

You Will Need:

  • Fine purple glitter (or another colour, if you must)
  • Original Mod Podge
  • A flat ended brush (about 10mm to 15mm wide)
  • A mixing pot (a yogurt pot or take out tub is perfect, especially if it has a lid)
  • An old teaspoon
  • Wooden laser cut shapes (I used 20mm and 30mm hearts, and 40mm stars)
  • Brooch backs and / or stick on pendant bails
  • E6000 glue

Purple glitter jewellery tutorial

How To:

1. Sprinkle about a teaspoon of glitter into your mixing pot (if you’re making a big batch just double this, and keep making fresh batches as you go, so none is wasted)

2. Add about the same amount of Mod Podge and mix them well with the spoon (then wash the spoon!)

3. Choose which side of your wooden shape you want to paint (there are often marks from the laser cutting on one side, so paint onto that as you won’t see it when you’re finished)

4. Paint a thin layer of the glittery glue onto your shape….best not to use too much at a time so that you don’t spill over the edges and it stays neat

5. Wait for that to dry and then paint on another thin coat

Purple glitter jewellery tutorial

6. Keep adding thin coats once the last is dry to build up the coverage….as with most painting projects, it’s better to do lots of thin coats than one or two thick ones (if your mixing pot has a lid you can cover your mixture whilst you wait for drying, so that it stays fresh)

7. I applied four or five coats to mine, and if you decide to make a big batch you can of course apply each coat to all of them, and by the time you’ve done the last, the first one will be dry and ready for the next

8. Once you’re happy with the coverage, leave until completely dry before flipping over ready for the backing

Purple glitter jewellery tutorial

9. If you’re using a brooch back, check it works ok before using it, then blob some E6000 onto the flat side of the brooch back and press it firmly onto the back of your wooden shape

10. If you’re making a pendant, blob the E6000 onto the flat pad of the bail and carefully press it onto the back of your shape….before it dries turn it over to make sure it’s on straight

11. Leave for 24 hours to dry well before adding a chain if you’ve made a pendant, or before proudly pinning your brooch onto your clothes!

Purple glitter jewellery tutorial

These would make great party favours for a Bridal Shower or Hen Party I think, or for children’s parties (although take care with brooch pins!)….or of course you could make some to raise funds for charity too!

Purple glitter jewellery tutorial

Ems x

Willow is the only national charity working with seriously ill young adults aged 16 to 40 to fulfil uplifting and unforgettable Special Days. These Special Days enable them and their families to reconnect and refocus on each other while enjoying an activity of their choosing. A day for them, a day about them and a day that will create memories they will all treasure forever.